Typically used between the battery bank and a 2000W or larger inverter

Sold by the foot

Typically used between the SPS and the main panel in systems designed for a 50A service

Sold by the foot

Class T Fuses are used as circuit protection between battery banks and inverters or alternators.

Dimensions: H 2.4" x W 7.1" x D 2.0"

This panel is intended both for Multiplus and Quattro inverter'/chargers. It allows PowerControl and PowerAssist current limit setting for two AC sources: a generator and shore side current for example.

Dimensions: H 1.7" x W 4.7" x D 2.6"

The VE.Bus Smart dongle is two products in one:

First of all it is the Bluetooth accessory for Victron’s range of inverter/chargers: Multiplus-I, MultiPlus-II, Quattros, and range extension of Phoenix Inverters with a VE.Bus port. When installed, use the VictronConnect App to monitor operation and also operate the system: change the input current limit as well as switch between Off, On and Charger-only modes.

Secondly it can work as a Voltage- and Temperature-sense device for the inverter/charger. This works with all models.

For monitoring, the device is a great alternative in caravans, smaller yachts and motor homes for which the Color Control GX or Cerbo GX are a step too far.

Please note that the MultiPlus or Quattro must be updated to the latest firmware in order to utilize the dongle.

Dongle Dimensions: H 0.9" x W 1.7" x D 4.2"
RJ45 Cable Length: 0.9m

The Color Control GX provides intuitive control and monitoring for all products connected to it. The list of Victron products that can be connected is endless: Inverters, Multis, Quattros, MPPT 150/70, BMV-600 series, BMV-700 series, Skylla-i, Lynx Ion and even more. This kit is not a battery monitor, but it does talk to battery monitors.

Allows for programming of an inverter using a PC.

Battery monitor kit with programmable relay. Measures voltage, current, capacity, and temperature. Can work with any battery type. Built-in Bluetooth. Compatible with the Color Control Monitor.

The BMV-712 is Victron's newest high precision battery monitor. The essential function of a battery monitor is to calculate ampere hours consumed and the state of charge of a battery. Compatible with all battery types. Built-in Bluetooth.

Monitor Dimensions: H 1.3" x W 2.4" x D 2.4"
Shunt Dimensions: H 1.4" x W 4.8" x D 1.6"
Cable Length: 10m

Easy start kits are typically installed on air conditioning units where the start-up surge might overwhelm an inverter. This kit also comes in a recommended Bluetooth version that allows for diagnostic feedback. Please note that the Bluetooth module does NOT allow you to control your AC unit.

Transparent Enclosure Dimensions:

• 7.64L x 3.58W x 2.50H in (194L x 91W x 64H mm)

Solid “Electro-Mechanical” connections are the only way to assure a continuous flow of electricity. The best way to make a solid crimp on BIG wire is with the HAMMER CRIMPER.

Clean, fray free wire ends assure the best connections. Good connections carry electricity with very little loss of “power”. And good, solid wire connections begin with a SHARP WIRE CUTTER.

Every electrical connection in an RV should be protected from corrosion by sealing the exposed wires. Heat Shrink does this. True, there are those who pull out a BIC to heat up shrink tubing, but unless you are way more experienced than lucky, then you need a TWO SPEED HEAT GUN.

Lost in the woods? Get out your Map and Compass to find where you are and where you need to go. So it is in Electrical Circuits, you need direction. From Design to Lay Out and Testing the only guide you’ll need is this solid, digitally accurate, fuse protected DIGITAL MULTIMETER.