Out on the range 200W 230A 200AhLi 2000VA
Out on the range 200W 230A 200AhLi 2000VA
- 2x 100W Solar Panels with mounts and wire harnesses
- 15A Victron SmartSolar MPPT Charge Controller with Bluetooth Communication
- Victron BMV-712 Battery Monitor with Bluetooth Communication
- 200Ah Lithium System with LifeBlue battery protections
- Integrated alternator charging with manual boost
- 2000VA Victron Multiplus pure sine inverter / 80A charger with hybrid 30A shore power
- Sub panel with multiple breakers and AC outlet
- 100A DC Battery Protect with remote disconnect prevents over discharge
- 6 position DC fuse block with DC outlet offering dual USB and standard 12V
- Shore power cord, inlet, lugs, heat shrink, cables, etc. All included
- $12,435 when installed by AM Solar with an estimated 38 hours of labor
This complete power system charges a single drop-in lithium battery with three different sources: solar, alternator and shore power. All charging and discharging systems are automatically regulated to optimize battery performance. This system can easily power LEDs, fans and cell phone chargers with DC, and on the AC side, shore power can go directly to the outlets when plugged in or power can be inverted from the battery when dry camping to cover loads like a blender, microwave or coffee pot.
What you get:
All the components needed to make a complete system
Installation manual with a full bill of materials
Connection diagrams detailing the entire system
AM Solar phone, email and Facetime support
Upgrade or Modification Options:
This complete kit is composed of five subsystems: Solar Charging, Battery Bank/Monitoring, Alternator Charging, AC Input/Output & DC Distribution. These subsystems can be removed or modified based on what you already have or want.
Solar
Changing the Panels: The charge controller can support a maximum of 450W, so 270W of solar panels with a similar Vmpp can be added. The easiest add-on would be more 90W panels assuming there is enough roof space. The current kit uses 2x 90W panels but these can be replaced with larger panels. You can also connect panels in series-parallel configurations if you have an even number, or use a larger commercial solar panel as long as you reinforce the mounts and only parallel panels of a similar Vmpp.
Change the Charge Controller: The current charge controller core is rated for 30A and uses 6ga cable. If you plan to use less solar wattage, a smaller core like the 15A might be more economical. Or, if you want more than 450W, check out our 50A charge controller core with 4ga cable.
External Port: An external charging port can be added that would allow for the use of folding panels as long as the charge controller can handle the extra wattage.
Battery Bank
AGM Batteries: The standard configuration of this kit comes with a Lithium battery, but it will work with AGM batteries. Check out our various Lifeline AGM battery options 6V 220Ah, 6V 300Ah, 6V 400Ah and 12V 255Ah. All batteries need to be the same make, model and age.
Different Lithium Batteries: The standard configuration includes one 200Ah battery. By adding a some cables, a Lynx distributor and some Mega Fuses, you can add up to three more 200Ah batteries or use different sizes like the 60Ah, 90Ah, 160Ah, or 300Ah. The Lithium Base Kit with the Lynx Distributor can support up to four batteries as long as they are all the same amp-hour rating.
AC and DC Distribution
More DC Outlets: The standard configuration comes with a 6 position fuse block. We have a 12 position block available. You can also get more outlets.
More AC Outlets: We include one AC outlet. If you need more, you can add them to the same breaker or other breakers in the sub panel.
Different Breakers: The standard configuration includes three duplex breakers 30/15, 20/15 & 15/15. There are many options.
Inverter/Charger System
Simplify the Inverter: If you don’t need the full 2000VA or a charger, you may be interested in one of our smaller stand alone inverter kits like the 250VA, 500VA, 800VA, or 1200VA. With these kits you also have the option of adding a shore power charger like a Progressive Dynamics 45A or 60A model or a clip on 7A charger.
Upgrade the Inverter: There is only a marginal price difference between the 2000VA and the 3000VA inverter systems. The 3000VA has a different footprint that might be better suited to some installation.
Monitoring
Upgrade the Display: Add a wall mounted MPPT Control to monitor the charge controller or a Victron Color Control GX Monitor to show complete system status on a single animated display.
Plan your build with these components:
This C-box is for efficiently combining solar panel output cables and sealing off a roof penetration. Its rugged and spacious design make installation and troubleshooting very easy. Do not use VHB tape on rubber (EPDM or TPO) roof material, all other roof types should use the taped option.
Dimensions: H 1.9" x W 11.61" x D 5.87"
Battery monitor kit with programmable relay. Measures voltage, current, capacity, and temperature. Can work with any battery type. Built-in Bluetooth. Compatible with the Color Control Monitor.
The BMV-712 is Victron's newest high precision battery monitor. The essential function of a battery monitor is to calculate ampere hours consumed and the state of charge of a battery. Compatible with all battery types. Built-in Bluetooth.
Monitor Dimensions: H 1.3" x W 2.4" x D 2.4"
Shunt Dimensions: H 1.4" x W 4.8" x D 1.6"
Cable Length: 10m
Because of Direct Current's tendency to arc when disconnected, special breakers are needed. These DC breakers are ideally used between charge controllers and battery banks and on alternator or small inverter lines.
Dimensions: H 1.8" x W 2.3" x D 3.5"
*Color may vary based on availability. This will have no effect on performance.*
Manually disconnect high current lines. This switch is typically used between a combiner box and a charge controller, or between a battery bank and an inverter.
Continuous Rating: 300A
Intermittent Rating: 500A (5 min)
Maximum Voltage: 48Vdc
Dimensions: 2 7/8"H x 2 7/8"W x 3 1/4"D
This panel is intended both for Multiplus and Quattro inverter'/chargers. It allows PowerControl and PowerAssist current limit setting for two AC sources: a generator and shore side current for example.
Dimensions: H 1.7" x W 4.7" x D 2.6"
Protect your batteries from accidental excessive discharge by installing a BP65 between your battery positive and DC distribution buss or fuse box. For loads under 65A.
Dimensions: H 1.9” x W 4.2” x D 1.9”
Class T Fuses are used as circuit protection between battery banks and inverters or alternators.
Dimensions: H 2.4" x W 7.1" x D 2.0"
The MultiPlus is a powerful true sine wave inverter, a sophisticated battery charger that features adaptive charge technology and a high-speed AC transfer switch in a single enclosure. Rated at 2000VA.
Note: Some Keurig coffee makers are known to be incompatible with inverters. In some cases, this will just result in a loud buzzing noise while operating, and in other cases, it will result in inverter overload and failure to operate. This doesn't mean your inverter will be damaged or that trying to use your coffee maker is dangerous; however, AM Solar cannot support compatibility issues resulting from a Keurig coffee maker. We recommend doing some research and purchasing a different coffee maker if you find yours to be incompatible with your inverter system.
Please note there is currently a nation-wide shortage of Duplex AC breakers (primarily 15/20). Our kits are designed to include these, but we may need to make substitutions due to stock level. Please email info@amsolar.com if you have any questions about this.
Steady State: 1600W
Surge: 4000W
Voltage Output: 120V AC
Voltage Input: 9.5-17V
No Load Draw: 3-9W
Waveform: Pure Sine
Frequency: 60hzCharger: 80A
Passthrough: 50A
Efficiency: 92%
Dimensions: H 19.70" x W 9.21" x D 5.75"
Extra: PowerAssist
Compact ATO/ATC fuse block consolidates branch circuits and eliminates the tangle of in-line fuses for electronics and other appliances.
Can be used for 24-hour circuits
Tin-plated copper buses and fuse clips
Accepts ring or spade type terminals
Accepts ATC and ATO fast acting blade fuses
Includes protective cover
Number of Circuits: 6
Mounting: (4) M4 Screws (Included)
Positive Bus Input Post: #10-32 stud
Negative Bus Input Post: #10-32 stud
Operating Voltage: 32V DC
Amperage Maximum Operating (per circuit) 30 Amps
Amperage Maximum Operating (per block) 100 Amps
Screw Terminals: #8-32 scews with flat washer and lock washer
Negative Bus: Yes
LED Blown Fuse Indicator: Yes
Polycarbonate base and cover material for rugged lightweight construction
Dimensions (L x W x H): 3.46 x 3.46 x 1.44 in
Fuses sold separately.
Standard 12V outlet with dual USB
Dimensions: H 4.1" x W 1.8" x D 2.1"
AC Distribution panel for 30A shore power systems
Dimensions: H 2.6" x W 3.0" x D 6.9"
This is a complete LifeBlue battery system with a Victron BMV-712 Bluetooth battery monitor.
Maximum Steady State Discharge Current: 150A DC
Maximum Surge Current (30 minutes): 200A DC
Battery Dimensions: H 10.8" x W 20" x D 6.9" 57lbs
AM Solar Part Number: 99-VANSLV
All lithium battery purchases are final.